Key takeaways
- A 14-inch band saw with at least 6 inches of resaw height and a 3/4-horsepower (or larger) motor suits hobbyists resawing lumber into bookmatched panels, while a benchtop or smaller 9- to 10-inch saw only makes sense for occasional thin-stock…
A 14-inch band saw with at least 6 inches of resaw height and a 3/4-horsepower (or larger) motor suits hobbyists resawing lumber into bookmatched panels, while a benchtop or smaller 9- to 10-inch saw only makes sense for occasional thin-stock work on boards under 4 inches wide.
Resawing is the toughest job most band saws are asked to do. Ripping a thick board into thinner slices along its width puts constant strain on the blade, the motor, and the guides, and it exposes weaknesses that never show up when the same saw is used for simple curve-cutting. Buyers shopping specifically for resawing need to look past the general “best band saw” lists and focus on three things: resaw capacity (the vertical distance between the table and the upper blade guide), motor power under sustained load, and the ability to track a wide blade without drifting.
What Actually Matters for Resawing
Resaw height is the single biggest differentiator. A saw with 6 inches of resaw capacity can split a 6-inch-wide board in one pass; anything less forces multiple flips and increases the chance of a wandering cut. Riser blocks, sold separately by some makers, add height to an existing saw but can introduce flex if the frame was not designed for it, so a saw with a tall factory frame is usually the safer long-term choice.
Motor power matters because resawing removes a wide kerf of material continuously, unlike scroll-style cuts that only engage a short section of blade. Reviewers consistently note that saws rated below 1/2 horsepower bog down in hardwoods over 4 inches thick, while 3/4- to 1-horsepower induction motors maintain blade speed through dense stock like maple or walnut.
Blade width and tension also drive resaw quality. Wider blades (3/4 inch to 1 inch) resist deflection better than the narrow blades used for scrollwork, but they need a saw with enough wheel tension capacity and a solid guide system — ideally ball-bearing or cool-block guides rather than basic pins — to keep the blade tracking true through a long cut.
Types of Band Saws Worth Comparing
14-Inch Cast-Iron Saws
This size class, often built around a two-wheel cast-iron frame, is the traditional sweet spot for home shops that resaw regularly. Stock height is usually 6 inches, and most accept an optional riser block to extend that further. Grizzly, Rikon, and Powermatic all sell saws in this category, and woodworking outlets regularly point to them as the baseline for serious resaw work.
Benchtop and Compact Saws
Smaller 9- to 10-inch benchtop saws are portable and inexpensive but typically cap out around 3.5 to 4 inches of resaw height with a fractional-horsepower motor. They can handle occasional resawing of narrower stock but struggle with wide hardwood boards and tend to need more passes and more sanding afterward.
Large Industrial and Hybrid Saws
Saws in the 17- to 20-inch range, often with 12 or more inches of resaw height and 1.5- to 2-horsepower motors, are built for shops that resaw veneer-thickness slices routinely or process thick slabs. They cost more, take up more floor space, and usually need 220-volt power, but they track wide blades with far less drift than smaller frames.
At a Glance
| Saw Class | Best For | Typical Resaw Height | Motor Range | Limits |
|---|---|---|---|---|
| 14-inch cast-iron | Regular hobbyist resawing, bookmatching | 6 in (up to 12 in with riser) | 3/4–1.5 HP | Riser kits can add minor flex; needs tuning |
| Benchtop/compact | Occasional, narrow-stock resawing | 3.5–4 in | 1/3–1/2 HP | Bogs down in thick hardwood; limited width |
| Large industrial/hybrid | Frequent veneer and slab resawing | 12+ in | 1.5–2+ HP | High cost, heavy, often needs 220V |
| Deep-throat specialty | Wide slab and bowl-blank resaw | 12–16 in | 2+ HP | Large footprint, premium pricing |
Pick X If…
| Situation | Recommended Type |
|---|---|
| You resaw a few boards a month for panels or boxes | 14-inch cast-iron saw with 6-inch resaw height |
| You mostly cut curves and only occasionally resaw narrow stock | Benchtop or compact 9- to 10-inch saw |
| You process slabs, veneer, or wide bowl blanks weekly | Large industrial or deep-throat saw with 12+ inch capacity |
| Your shop space and power supply are limited | 14-inch saw with riser block option rather than a full-size industrial unit |
Fit, Setup, and Compatibility Notes
Blade width should match the saw’s maximum rated width before buying a dedicated resaw blade; most 14-inch saws top out around 3/4 inch to 1 inch, while benchtop saws are often limited to 1/2 inch or less. Check wheel tires and guide bearings periodically, since resawing generates more heat and blade wear than light curve work, and a worn tire can let a wide blade slip during a long cut.
Table size and fence quality matter more for resawing than for scrollwork because a tall board needs firm, consistent support against a resaw fence or a pivot-style fence. A saw with a short, flimsy stock fence benefits from an aftermarket or shop-made tall fence to keep the board square to the blade through the entire cut.
Power requirements differ by class: most 14-inch saws run on standard 120-volt household circuits, while many larger industrial saws need a dedicated 220-volt circuit. Confirm electrical compatibility with a dedicated shop circuit before choosing a saw that exceeds standard outlet capacity.
A Few Alternatives Worth Knowing
A quality two-wheel 14-inch saw without a riser block is a reasonable alternative for buyers who resaw stock under 6 inches wide and want to avoid the extra cost and setup of a riser kit. A three-wheel band saw, which trades resaw depth for a larger cutting throat at a lower blade tension, is a niche alternative favored by some for curve work but is generally considered a weaker choice specifically for resawing because the design limits how wide a blade it can run. For buyers who only need occasional resaw capability and already own a table saw, a thin-kerf rip blade and multiple passes is a lower-cost workaround, though it wastes more material and leaves a rougher surface than a dedicated band saw resaw.
Frequently Asked Questions
What resaw height do I actually need?
Match the saw’s resaw height to the widest board you plan to cut in one pass. Most hobbyist resawing of cabinet-grade lumber falls between 4 and 8 inches, so a saw with 6 inches of stock capacity, or more with a riser block, covers the majority of projects. Only slab or veneer specialists typically need 12 inches or more.
Does motor horsepower matter more than blade quality for resawing?
Both matter, but they solve different problems. Motor power keeps the blade moving at a consistent speed through dense or wide stock, while blade design (tooth count, set, and width) determines how straight and smooth the cut tracks. A strong motor paired with the wrong blade can still produce a wandering cut.
Can a benchtop band saw resaw hardwood boards?
A benchtop saw can resaw narrow or softer hardwood boards within its rated capacity, but reviewers note that fractional-horsepower motors slow down noticeably in dense woods over a few inches thick. For routine resawing of wide hardwood stock, a full-size saw with a larger motor is the more reliable choice.
Do I need a riser block, or should I buy a taller saw outright?
A riser block is a cost-effective way to add resaw height to an existing 14-inch saw, but it adds frame height without adding frame rigidity, which can introduce slight blade flex on very tall cuts. Buyers who know they need maximum resaw capacity from the start often get better long-term results from a saw built tall at the factory.
What blade width should I buy for resawing?
Wider blades, generally 1/2 inch to 3/4 inch with fewer teeth per inch, track straighter through thick resaw cuts than the narrow blades used for curves. Confirm the saw’s maximum blade width rating first, since not every saw’s wheels and guides can tension a wide blade properly.
How do I stop my resaw cuts from drifting off the line?
Drift usually comes from blade tension, a dull or poorly set blade, or an improperly aligned fence. The maker’s manual typically outlines a tracking and tension-check procedure; following it before each resaw session, along with using a dedicated resaw fence set to compensate for any natural lead, resolves most drift issues reviewers describe.
You might also like